Download
Name VariCam LT Software (Firmware) Update Data
Last Update June 12, 2017
Model AU-V35LT1G, AU-V35LT1MC
Registered
Name/Size		 VSI6227L / 78.6MB
Expected Time for Update Approx. 60min
© Panasonic Entertainment & Communication Co., Ltd.
Transfer All Rights Reserved
Software This software is update data for the applicable model above.
Content  Ver 24.08-00-0.00
  1. Support for 240/200p RAW output with 2K/HD CROP
    (1) 2K/10bit and HD/10bit are added to SDI RAW menu.
    (2) HIGH SPEED menu is added for the OFF setting of MAIN CODEC.
    When FREQUENCY is 59.94p/29.97p/24p/23.98p;
    SDI RAW MAIN PIXEL MAIN CODEC HIGH SPEED FPS*
    2K / 10bit
    (HD/10bit)    		 2048x1080 CROP
    (1920x1080 CROP)    		 AVC-Intra 2K 422 - 1-120p
    AVC-Intra 2K LT - 1-240p
    OFF OFF 1-120p
    ON 1-240p
    * When FREQUENCY is 50p/25p; 1-120p → 1-100p, 1-240p → 1-200p
  2. The lower limit of FPS setting range is extended.
    When HIGH SPEED is ON, FPS can be set from 1.
    (While AVC-Intra-LT/AVC-Intra2K-LT/AVC-Intra4K-LT format is selected, HIGH SPEED is ON automatically. The following range also apply in this case.)
    FPS Setting Range: So far 120-240p / 100-200p / 60-120p / 50-100p
    → Changed to 1 - 240p / 1 - 200p / 1- 120p / 1 - 100p
  3. Firmware is improved so that SINGLE can be selected for RAW OUTPUT while MAIN CODEC is OFF.
    So far, DUAL/SINGLE selection for RAW OUTPUT has been allowed when the following requirements are met.
    (1) FREQUENCY is 29.97p or lower.
    (2) SDI RAW is 4K/10bit or UHD/10bit.
    (3) MAIN CODEC is AVC-Intra4K 422.
    → By this update, the requirement (3) is changed to the following one.

    (3)’ MAIN CODEC is AVC-Intra4K 422 or OFF.
    When MAIN CODEC is OFF, the setting range of FPS is as follows.
    ・ When RAW OUTPUT is SINGLE; 1-30p (1-25p)
    ・ When RAW OUTPUT is DUAL; 1-60p (1-50p)
  4. Icons are added for indicating FF/REW playback.
    The 16x high-speed playback function is added.
  5. RESTART function is added to the control panel.
    RESTART button is added so that the camera can be rebooted by means of the control panel, instead of the power switch, after the system mode is changed.
  6. REC CHECK function is added.
    Playback function of the first or last 5-second footage of the last clip recorded after the power is turned on
    This is used after it is assigned to a User SW.
    The following items are added for assignment to USER1 – 3.
    - CHECK LAST CLIP START ・Playback of the first 5-sec
    - CHECK LAST CLIP END　　・Playback of the last 5-sec
  7. DESQUEEZE in playback is supported.
    Firmware is changed so that not only EE output but also a played clip is shown using DESQUEEZE when MENU -> ANAMORPHIC DESQUEEZE -> DESQUEEZE is ON.
  8. Support for Add/Delete function of SHUTTER and WB via ROP App
    Supported App: VARICAM ROP Ver. 1.0.3 or later
  9. Default setting for monitor output indication of USER CLIP NAME is changed to OFF.
    OUTPUT SETTINGS Menu
    SDI OUT INDICATOR ->USER CLIP NAME（TYPE3) ->USER CLIP NAME:OFF
  10. A compatible EF lens is added.
    EF24-105mm F4L IS USM (Canon)
  11. Supported wireless LAN modules are added.
    AJ-WM50MC (China) Automatic Channel Switching
    GW-900D (PLANEX, Japan)

    Improvement
  12. The indicator for remaining card capacity is corrected because it has a problem when the format is Long GOP on 23.98p of Frequency.

 
History of release notes
Preparation
for Upgrade		 Copy the update file of the Software (Firmware) to an SD memory card.
Software can be updated using this SD memory card.
Please refer to the procedure in the site.(Printing out of the procedure is recommended.)